Kontron SYMKLOUD MS2900 Web Uživatelský manuál

» Quick Start Guide « www.kontron.com Kontron SYMKLOUD MS2900 Platform Document revision 1.0

10 www.kontron.com Quick Start Guide Figure 3: Connecting the AC Power Cord and Grounding Cable Figure 4: Connecting the DC Power Cord and Groundi

11 www.kontron.com Quick Start Guide In addition to plugging in the power cord, you must also attach the grounding wire on the connector to the grou

12 www.kontron.com Quick Start Guide Figure 6: MS2900 Front I/O Connections I/O Port Description 1 Management 1GbE RJ-45 port (Switch/ShMC 1) (

13 www.kontron.com Quick Start Guide For information about port mapping for the 10GbE and 1GbE connections, see Figure 11 in the ‚Configuring Switch

14 www.kontron.com Quick Start Guide 3 First Power-Up This chapter covers what to expect when you boot up the system for the first time. Both norma

15 www.kontron.com Quick Start Guide » Fans speed up to the maximum level and stay there. The fan manager on the ShMC does not slow them down. The

16 www.kontron.com Quick Start Guide Figure 9: MS2900 Front and Rear LEDs

17 www.kontron.com Quick Start Guide 4 Basic Configuration This chapter covers the following topics: » Configuring your system network » Configur

18 www.kontron.com Quick Start Guide Figure 10: IP Addresses When configuring the MS2900 system, set up your equipment (e.g., a laptop) to use the

19 www.kontron.com Quick Start Guide Figure 11: Hub and Processor Node Port Mapping On both Hub 1 and Hub 2, port 2, labeled ’’2’’ on the hub face

2 www.kontron.com Quick Start Guide » Table of Contents « 1 Before You Get Started ...

20 www.kontron.com Quick Start Guide Using a Serial Console 4.1.2You can access the components of your MS2900 platform by using the MSH8900 seria

21 www.kontron.com Quick Start Guide Configuring Processor Nodes through the ShMC 1. Switch the serial console MUX to address the ShMC, as follows:

22 www.kontron.com Quick Start Guide Configuring Switches To change the serial console MUX to address a switch, follow these steps: 1. Press CTRL g

23 www.kontron.com Quick Start Guide 4. To change the password for the touch login, enter the command eqcli > user touch password and follow th

24 www.kontron.com Quick Start Guide 5 Running an Operating System The SYMKLOUD MS2900 platform can be shipped with or without a pre-installed oper

25 www.kontron.com Quick Start Guide The Setup default values are the optimum performance settings for all devices and system features. However, you

26 www.kontron.com Quick Start Guide 6 Making Sure Your System is Up-to-Date This chapter presents the provisions Kontron has for helping you ensur

27 www.kontron.com Quick Start Guide 2. Type the following values into the form: USERNAME: admin PASSWORD: admin and click Sign in to access the S

28 www.kontron.com Quick Start Guide The system status bar showing the overall system status and the fan speeds is displayed at the top of all the S

29 www.kontron.com Quick Start Guide Figure 15: System Monitor Main Page (Processor Node Information Example) When processor nodes are selected f

3 www.kontron.com Quick Start Guide 7.2 Contact Information ...

30 www.kontron.com Quick Start Guide Right Side Panel - Software Upgrade Views 6.1.3Figure 16 shows an example of the System Monitor main page wit

31 www.kontron.com Quick Start Guide Figure 17: System Monitor Main Page (Processor Node Software Upgrade Example) In this example, for processor

32 www.kontron.com Quick Start Guide Figure 18: One Click Upgrade Page (Processor Nodes Example) Right Panel SYMbalance View (Nodes 7 and 9) 6.

33 www.kontron.com Quick Start Guide Figure 19: SYMbalance Settings

34 www.kontron.com Quick Start Guide 7 Additional Resources This chapter provides information about where additional SYMKLOUD MS2900 Platform produ

35 www.kontron.com Quick Start Guide 8 Trademarks and Copyright 8.1 Copyright Notice Copyright © 2013 Kontron America Inc. All rights reserved. No

36 www.kontron.com Quick Start Guide Corporate Offices Europe, Middle East & Africa Oskar-von-Miller-Str. 1 85386 Echin

4 www.kontron.com Quick Start Guide » Table of Figures « Figure 1: Components for Initial Set-Up ...

5 www.kontron.com Quick Start Guide 1 Before You Get Started Caution! The SYMKLOUD MS2900 Platform is ESD sensitive equipment. Users must observe p

6 www.kontron.com Quick Start Guide 1.2 Equipment You Need to Set Up Your System Figure 1 shows what you will need to get started. For instructions

7 www.kontron.com Quick Start Guide Figure 1: Components for Initial Set-Up

8 www.kontron.com Quick Start Guide 2 Getting Started This chapter covers how to set up the MS2900 platform for installation in a cabinet/rack and

9 www.kontron.com Quick Start Guide Figure 2: Attaching the Slide Rails to the Chassis 2.2 Connecting Power Cords NOTE: When using a rack, wait to