Kontron M2M Smart Services Developer Kit Wind River Intell Uživatelský manuál

Kontron M2M Smart Services Developer Kit Wind River Intelligent Device Platform LiveUSB Getting Started Guide Document Revision 1.15 Part

10

11 3 Starting the Evaluation Software 3.1 Booting the Host Computer Before booting your host computer, ensure that the LiveUSB flash drive is corre

12 3.4 License Activation on an Internet connected host If the host on which you will be running your evaluation is connected to the Internet then t

13 4. Once completed press the Save Changes button and then press the Next button (from the previous screen shot). 5. Fill in your registration

14 3.5 3rd Party Software Evaluation License If you are not planning to evaluate the Prosyst OSGi software, then you may safely skip this section.

15 3.6 Starting Your Software Evaluation After the host computer boots into the Fedora LiveUSB environment, you will see a desktop that includes a n

16

17 Appendix A: Manual License Activation A.1 Manual License Activation on a non-Internet connected host If the host on which you will be running your

18 4 5. Once you have read and understood the Wind River Privacy Statement, select the tick box to acknowledge your agreement. 6. Click the Su

19 7. The user_registration.txt file should be emailed, as an attachment, to [email protected]. A Wind River service representative from the Wi

www.kontron.com www.kontron.com » Table of Contents « 1 Introduction ... 4 1.1 About this Manual & How

20 Appendix B: Troubleshooting Your Evaluation Setup B.3 Network Topology Overview B.3.1 Retrieving the evaluation license: To retrieve the evaluati

21 4. Perform the steps in section 3.3 to complete your license activation.

22 Appendix C: Troubleshooting Graphics Problems on Your LiveUSB Host Computer The LiveUSB was validated with many different host computers, but some

23 Appendix D: Recovering Your Linux Image on the Kontron M2M System Your Kontron M2M System comes factory-installed with Wind River Intelligent Devi

24 D.1 Making the Evaluation Image Recovery Tool USB Drive Before you make a bootable recovery USB image, you must have booted the host computer fro

25 D.2 Recovering your Kontron M2M System Software Evaluation System 1. Disconnect the power adapter from AC power to turn off your system. 2. You

26 11. Reconnect the power adapter to AC power to turn on your system 12. The Kontron M2M System target now boots into the Qt Graphics Suite demonstr

27 Appendix F: Installing the LiveUSB to VMWare Virtual Machine The following instructions will step you through installing the LiveUSB into a VMWar

28 Note: the Virtual Machine will be running in a small window. This is expected during the installation processes. Once installation has completed,

29 Document Revision History Revision Date Author Description 1.0-1.04 2011 Staff Initial release and various updates throughout 1.05 8 May 2012 CAV

www.kontron.com www.kontron.com D.1 Making the Evaluation Image Recovery Tool USB Drive ... 23 D.2 Recovering yo

30

31 Corporate Offices Europe, Middle East & Africa Oskar-von-Miller-Str. 1 85386 Eching/Munich Germany Tel.: +49 (0)8165/

4 1 Introduction Welcome to the Wind River Intelligent Device Platform LiveUSB Getting Started Guide. Using the specially configured evaluation envi

5 This kit includes the following components: The Kontron M2M System, pre-flashed with a Wind River Intelligent Device Platform kernel and root file

6  A fully configured and bootable version of the Fedora (Linux) operating system  The Wind River Intelligent Device Platform, which includes the

7 2 Connecting the Hardware 2.1 Ports and Antennas Refer to the figure below for locations of ports and where to attach the antennas: Note: The

8 2.2 Peripheral Hookup Connect an HDMI Monitor, a USB Hub, Mouse and Keyboard to the Development Target as shown below. DevelopmentTargetMouseUSB

9 1DevelopmentTargetWANRouterEvaluationHostLiveUSBWAN Figure 2 Connecting the Host to the Target 2.4 Powering the Kontron M2M System You should ens