Kontron CG2100 Carrier Grade Server Uživatelský manuál Strana 25
- Strana / 110
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
24
To remove the riser card assembly:
1. Power down the server and remove all peripheral devices and the power cord(s)
2. Remove the back chassis cover. For instructions, see “Removing the Chassis Covers”
in Section 3.2.
3. Loosen the blue captive thumb screw (Figure 12, “B”) at the rear of the chassis.
Notice the guide pins that will be used to re-install the riser assembly into the
chassis. (“A”)
4. Lift the riser card assembly out of the chassis.
5. If there is a riser card in the assembly, rest the assembly upside-down with the
sheet metal cover on the bottom so the assembly is not resting on the card edge.
Figure 12. Riser Card Assembly Retention Screw
Re-Installing the Riser Card Assembly
To re-install the riser card assembly:
1. Position the riser front tab guide hole over the guide pin on the server board. See
Figure 13, (“C”).
2. Make sure the forks on the back of the assembly rest securely on the guide pins on
the rear of the chassis (“B”).
3. Using the blue touch points on the top of the assembly (A), press down to mate the
riser card with the header on the server board.
NOTE: To avoid damaging the card edge, be sure that the card is lined up straight with
the header, not on an angle.
4. Tighten the blue retention screw on the rear of the chassis. See Figure 12.
5. Replace the chassis back cover. For instructions see “Re-Installing the Back Cover”
in Section 3.2.
Figure 13. Installing the Riser Card Assembly
- Document Revision 1.2 1
- » Table of Contents « 2
- 1 Introduction 7
- 1.4 Product Accessories 8
- 2 Features 10
- 2.1 Server Components 11
- 2.4 Front Panel Board 16
- 2.5 LED/Switch Board 16
- 2.6 Hard Disk Drives 16
- 2.7 SD Flash Module 17
- 2.9 Riser Card Assembly 18
- 2.10 Ethernet NIC Ports 19
- 2.12 Power Supply Subsystem 19
- 2.13 System Cooling 20
- Processors 21
- Upgrades 22
- Removing the Back Cover 23
- Re-Installing the Back Cover 23
- Removing the Front Bezel 24
- Installation Procedures 27
- Supported Memory 28
- Publishing System Memory 28
- Memory RAS 29
- Memory Upgrade Rules 31
- Installing Memory DIMMs 32
- Removing a Processor 34
- Installing a New Processor 35
- Inserting the Heat Sink 36
- Procedures 39
- Figure 25. Cable Routing 40
- Table 5. System Cables 40
- Connecting the Power Cord 58
- Equipment Rack Precautions 58
- 5.1 Before You Begin 60
- 5.2 Replacing Fans 60
- Replacing 80mm CPU Fans 61
- Replacing 60mm PCI Fans 61
- Removing the Bridge Board 62
- (Figure 69, “A” and “B”) 77
- 6 Server Utilities 79
- 6.2 Upgrading the BIOS 81
- 6.4 Clearing the Password 82
- 7 Troubleshooting 84
- Power Light does not Light 86
- 7.5 LED Information 89
- BIOS POST Beep Codes 91
- 8 Warranty 93
- 9.1 Emissions Disclaimer 94
- 9.2 Intended Uses 94
- 9.3 Safety Cautions 96
- Wichtige Sicherheitshinweise 97
- Consignes de sécurité 99
- Certification Information 106
- FCC (USA) 107
- Industry Canada (ICES-003) 107
- VCCI (Japan) 108
- BSMI (Taiwan) 108
- 11 Appendix C: Getting Help 109
Související produkty a manuály pro Počítačový hardware Kontron CG2100 Carrier Grade Server
(114 stránky)
(49 stránky)IKEA BARMHARTIG 802.847.2 manuály
Uživatelské manuály a uživatelské příručky pro ne IKEA BARMHARTIG 802.847.2.
Poskytujeme 1 manuály pdf IKEA BARMHARTIG 802.847.2 ke stažení zdarma podle typů dokumentů: Instalační manuál
Komentáře k této Příručce