Kontron NSC2U IP Network Server Uživatelský manuál Strana 118
- Strana / 152
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
NSC2U Server—5
Kontron IP Network Server NSC2U
Product Guide, rev. 1.4 December 2009
118
5.6.2 Installing the Server Board Back into the Chassis
1. Set the replacement board into place (Figure 104, “A”), using caution to make sure
no cables are pinched under the board. Insert the rear edge of the board first, and
line up the I/O ports at the rear of the system.
2. When placing the board into the chassis, make certain that the board does not
catch on the fan alignment bracket (“B”). Note the that bracket must reside under
the insulator.
3. Make sure the standoff locations line up correctly and reinsert the six screws
removed previously. (“C”)
Figure 103. Removing the Server Board
A
B
TS000570
- Product Guide 1
- Rev. 1.4 1
- Legal Lines and Disclaimers 2
- Contents 3
- NSC2U Server—Contents 4
- Revision History 7
- NSC2U Server—Revision History 8
- 1 Introduction 9
- 1.3 Product Accessories 10
- Introduction—NSC2U Server 11
- 2Features 12
- 2.1 Server Components 14
- 2.2 NSC2U Server Back Panel 15
- 2.3 NSC2U Server Front Panel 15
- TS000112 17
- 2.5.1 SFP Board Features 18
- Features—NSC2U Server 19
- 2.9 Power Supply 21
- 2.10 System Cooling 21
- 2.10.3 PCI Cooling Area 22
- 2.10.5 Fan Speed Control 23
- 2.10.6 Cooling Summary 23
- 2.11 Hardware Requirements 24
- 3.1 Before You Begin 25
- TS000543 26
- TS000272 27
- TS000544 28
- TS000274 29
- TS000219 30
- AF000810 30
- TS000275 31
- AC PS DC PS 32
- 3.4.1.1 Configuration Jumpers 33
- 3.4.1.2 BIOS Select Jumper 33
- 3.4.2.1 Memory RASUM Features 36
- 3.4.2.2 Supported Memory 36
- TS000300 40
- 3.4.3 Installing DIMMs 41
- Branch 0 42
- Branch 1 42
- 3.4.5.2 Removing a Processor 44
- AF000768 45
- AF000770 46
- AF000771 46
- AF000772 47
- 4.1 Before You Begin 50
- 4.2.1 Riser Card Options 52
- TS000545 53
- TS000280 54
- Full-height Add-in Cards 55
- TS000546 56
- 4.4 Installing Intel 57
- Remote Management Modules 57
- GCM3 ModuleRMM Module 58
- TS000320 59
- TS000319 60
- TS000550 61
- TS000551 62
- TS000552 63
- TS000328 64
- TS000327 64
- TS000329 65
- TS000511 66
- TS000512 67
- TS000513 68
- TS000514 69
- TS000515 70
- TS000516 71
- TS000517 72
- TS000518 73
- TS000519 74
- Figure 59 75
- TS000521 76
- TS000522 77
- TS000523 78
- TS000524 79
- TS000525 80
- TS000526 80
- TS000527 81
- TS000528 82
- TS000529 83
- TS000530 84
- 4.6.4 Re-assemble the System 85
- TS000532 86
- TS000533 87
- TS000534 88
- TS000535 89
- TS000536 90
- TS000502 91
- TS000503 92
- TS000284 93
- TS000301 94
- TS000302 94
- TS000303 95
- TS000554 96
- TS000555 97
- 5.1 Before You Begin 98
- TS000556 99
- 5.2.1 Removing the CPU Fans 100
- 5.2.2 Replacing the CPU Fans 101
- NSC2U Server—5 102
- TS000560 103
- TS000562 105
- TS000564 107
- TS000565 108
- TS000566 109
- Backplane Board 110
- TS000313 111
- Assembly 112
- TS000316 113
- TS000568 115
- TS000569 116
- TS000570 118
- TS000537 119
- TS000308 121
- 6 Server Utilities 122
- 6.2 Upgrading the BIOS 123
- 6.2.1.2 Obtaining the Upgrade 124
- 6.3 Clearing the CMOS 124
- 6.4 Clearing the Password 125
- 7 Troubleshooting 126
- NSC2U Server—7 128
- 7.5 LED Information 131
- 7.6 BIOS Error Messages 132
- 7.6.1 BIOS POST Beep Codes 133
- 8 Warranty 135
- NSC2U Server—8 136
- A.1 Emissions Disclaimer 137
- A.2 Intended Uses 137
- NSC2U Server—A 138
- A.3 Safety Cautions 139
- Wichtige Sicherheitshinweise 140
- Consignes de sécurité 142
- Information en 144
- B.2.1 FCC (USA) 148
- B.2.4 VCCI (Japan) 149
- B.2.5 BSMI (Taiwan) 149
- NSC2U Server—B 150
- Appendix C: Getting Help 151
- NSC2U Server—C 152
Související produkty a manuály pro Počítačový hardware Kontron NSC2U IP Network Server
(103 stránky)
(49 stránky)Hotpoint WMEF 943P UK manuales
Manuales del propietario y guías del usuario para Lavadoras Hotpoint WMEF 943P UK.
Ofrecemos 2 manuales en pdf Hotpoint WMEF 943P UK para descargar gratis por tipos de documentos: Instrucciones de uso
Komentáře k této Příručce